Poured liners
A cement based mix is poured around a form inside the chimney to create a smooth new flue in a single solid lining.
A Avonmore chimney sweep can reline your chimney with a liner sized to the appliance and insulated where the system calls for it. One call to (724) 817-2006 reaches a nearby sweep who installs liners.
Inside most chimneys is a liner, the tube that actually carries smoke and flue gases to the top. It keeps heat from reaching wood framing next to the chimney, protects the brick and mortar from corrosive gases and gives the appliance a flue of the right size to draft well. Some older chimneys were built unlined, and others have clay tiles that have cracked over the decades.
Most liner installations start with one of these situations. Clay tiles crack after chimney fires, shift as the house settles and lose mortar at the joints, while some chimneys never had tiles to begin with. Installing an insert, stove or high efficiency furnace often means the old flue is the wrong size.
Industry standards based on NFPA 211 call for a Level 2 inspection when an appliance is changed or after a chimney fire. The inspection tells you whether relining is truly needed and what kind of liner suits the chimney. Seeing the inside of the flue makes the decision much easier.
Chimney Liner Installation is often paired with chimney liner repair and chimney inspection, depending on the cause.
Looking for Avonmore chimney liner installation? Call (724) 817-2006 and describe the problem to a chimney sweep who works in Avonmore.
Call nowHere is how a sweep usually handles a liner installation.
A camera is run through the flue to check the existing tiles, offsets and obstructions. This confirms what kind of liner the chimney needs.
Sizing follows the appliance it will serve, since too big or too small both cause problems. The length is measured from the appliance to the top of the chimney.
The flue is swept and any loose tile or obstruction is cleared so the liner can pass. Some chimneys need old tiles broken out to fit an insulated liner.
The liner goes in from the top, with insulation added where the system requires it. Insulating it helps draft and reduces creosote and condensation.
At the top, a plate and cap close off the flue, and at the bottom the liner connects to the appliance. The connections keep gases from leaking into the old flue.
A draft test confirms the new liner is working. This is also a good time to test your CO alarms.
A cement based mix is poured around a form inside the chimney to create a smooth new flue in a single solid lining.
Rigid stainless sections join together in straight chimneys which suits wood burning appliances well.
Flex liners snake through chimneys with bends and offsets which makes them the most common relining choice.
An insulation wrap or poured insulation surrounds the liner where the system or chimney calls for it.
A properly sized liner for a water heater left alone after a furnace upgrade to keep combustion gases moving out of the house.
A stainless steel liner is the standard choice for most homes that need a new flue. Flexible liners make it possible to reline chimneys with offsets, while rigid pipe gives a smooth, heavy wall. Liners are sold as tested systems, with grades suited to wood, gas or oil.
Stainless liners are often paired with insulation, either a wrap or a poured mix, which keeps flue gases warm and can be required for clearance to combustibles. At the top, a sealing plate and cap keep rain and animals out. In Avonmore, a stainless liner is a common upgrade when installing an insert or wood stove.
Chimney relining is the process of lining a flue again when the original liner is cracked, missing or unsuitable. The most common triggers are chimney fires, settling cracks, missing mortar and appliance changes. Most chimneys can be relined from the roof without opening walls.
When you call (724) 817-2006, tell the sweep what vents into the chimney, such as a fireplace, stove, furnace or water heater. A furnace replaced with a high efficiency model that vents through the wall can leave the water heater alone in an oversized flue, which leads to poor draft and condensation. Relining with the right size solves the draft and moisture problems.
Around Avonmore, relining usually comes up when a home changes heating appliances or an inspection turns up cracked tiles. Across Avonmore and nearby towns such as Vandergrift, Delmont, Hyde Park and Murrysville, long heating seasons and repeated freeze and thaw cycles are hard on clay tile and mortar, which is why relining is one of the most common chimney upgrades in the area.
Need chimney liner installation around Avonmore? Call (724) 817-2006 for an Avonmore chimney sweep who serves the towns around it too.
Cold winters keep fireplaces, wood stoves and oil burners working for half the year or more. Masonry takes the worst of it from the freeze and thaw cycle: rain and melting snow soak into the crown and joints, then freeze and push them apart, and each winter widens the cracks a little more. Nor'easters drive rain sideways into flashing and mortar that looked fine in summer. Most homeowners in Avonmore, PA schedule a sweep in early fall, and a repair check after a hard winter.
Small chimney problems caught early usually stay small repairs.
Chimney sweeps in Avonmore know the chimneys and fireplaces common in local homes.
Ask your questions before you agree to anything.
More questions? Call (724) 817-2006
Restoring a damaged chimney liner so smoke and gases stay sealed inside the flue.
Learn moreA level 1, 2 or 3 review of the full chimney system so you know whether it is safe to light a fire.
Learn moreInstalling wood, gas and pellet inserts in existing fireplaces, sized to the firebox and vented through a full-length liner.
Learn moreWood stove installation into an existing chimney or a new insulated chimney, following the stove manual and local code.
Learn moreLooking for something else?
See all chimney servicesCall now for Avonmore chimney liner installation and help in the towns around it.
Free to call. No forms to fill out.